On-vehicle system for acquisition of strain and voltage signals
The Kyowa DIS-7000 Series is a modular, multi-channel on-board data logger that rides in the vehicle during automotive crash testing. It measures strain gage sensors and voltage signals, fires airbag igniters on a preset delay, and records CAN/CAN FD bus data to built-in memory. It handles impacts of 100 G and scales to 1,056 synchronous channels.
Up to 1,056 synchronous channels: up to 999 when using DIS-70A control software
Impact resistance: 980.7 m/s² (100 G), 10 ms half-sine
Compact and lightweight: 168 channels in 11.42 × 3.94 × 8.27 in (290 W × 100 H × 210 D mm), approx. 19.8 lb (9 kg)
Built for purpose: master module plus up to 15 expansion modules per master
Airbag ignition: outputs ignition current based on the preset delay time (DIA-708A)
CAN/CAN FD recording: DIC-706B
Built-in Li-ion batteries: approx. 30 minutes of continuous operation
TEDS compatible: IEEE 1451.4, with sensor ID
What it is used for
Some of the use cases for the DIS-7000 Series include:
Full-vehicle crash tests — on-board measurement in actual vehicle impact testing, such as offset crash tests
Dummy instrumentation — measuring the sensors installed on crash test dummies
Airbag deployment timing — firing igniters on a preset delay during the test
Vehicle network recording — capturing CAN and CAN FD data during the impact
Features
Compact & lightweight (168 channels in 290 W × 100 H × 210D mm, approx. 9 kg)
High impact resistant: 100 G
Synchronous measuring channels up to 1056 (Up to 999 channels when using DIS-70A)
Outputs ignition current based on the pre-set delay time. (DIA-708A)
Records the CAN/CAN FD data. (DIC-706B)
What does the DIS-7000 Series measure?
The DIS-7000 Series is a compact crash test measurement system that can be loaded in vehicles during automotive crash testing to measure sensors and signals and record the data to built-in memory. Testing uses this special on-board measurement system, with impact resistance, connected to various sensors including those installed on dummies.
The system is modular, so it can be built for purpose:
Module
Model
Function
Master module
DIS-7000A
Controls the DIS-7000 series; 32 digital inputs, 4 trigger distribution outputs
Signal conditioner module
DIS-724A-T
24 channels for strain and voltage, square connector type
Signal conditioner module
DIS-724A-L
24 channels for strain and voltage, round connector type
Airbag timer module
DIA-708A
8 channels of ignition current output with preset delay
CAN FD measurement module
DIC-706B
6 channels of CAN/CAN FD bus data recording
Control software
DIS-70A
Recording and control from a PC (PC optional)
Up to 15 expansion modules connect to each master module, with up to 48 units in total, including up to 4 master modules. The system also supports trigger synchronization with previous DIS-5000 Series devices.
Why engineers pick it
Survives the crash it measures. Every module is rated for 980.7 m/s² (100 G), 10 ms half-sine, 1,000 times in each of the X, Y, and Z axes.
High channel count in a small, light package. A master module and seven 24-channel signal conditioners give 168 channels in 290 × 100 × 210 mm, at approximately 9 kg.
One system for sensors, igniters, and the vehicle bus. Strain and voltage channels, airbag timer outputs, and CAN/CAN FD recording all share the same trigger and synchronization.
Fits existing vehicle mounting plates. L angle brackets with the same mounting pitch as conventional DIS-5010A products let you keep using conventional vehicle mounting plates.
How is a DIS-7000 system configured?
Start with a DIS-7000A master module, then add the expansion modules your test needs:
Strain gage sensors and voltage signals: DIS-724A-T (square connector) or DIS-724A-L (round connector), 24 channels each, 100 kHz sampling, 16-bit
Airbag ignition: DIA-708A, 8 channels, 0.5 to 3.0 A output current, delay of 0.1 to 9,999 ms
CAN or CAN FD data: DIC-706B, 6 channels with timestamps
Control and data handling: DIS-70A control software on a Windows PC
Expansion modules connect directly to the master module through a D-sub connector, or through an extension cable of up to 2 m (6.6 ft). Master modules connect to each other, and to conventional products, through cascade cables of up to 10 m (32.8 ft).
Every module runs from 15 to 28 VDC (typical 24 VDC). Kyowa recommends its own external power supply; with other supplies, some items, including the number of units, may not meet specifications.
When is the DIS-7000 Series the wrong choice?
Long recording sessions. Recording time is approximately 80 minutes at 100 kHz on the master and signal conditioner modules, and approximately 40 minutes at 100 kHz for the DIA-708A current waveform.
Extended battery-only operation. Built-in batteries give approximately 30 minutes of continuous operation.
Operating temperatures outside 32 to 122 °F (0 to 50 °C). That is the specified operating range.
DIS-7000 Series FAQ
Up to 1,056 synchronous channels, or up to 999 channels when using DIS-70A control software.
980.7 m/s² (100 G), 10 ms half-sine, 1,000 times in each of the X, Y, and Z directions.
Up to 48 units, including up to 4 master modules. Each master module controls up to 15 expansion modules.
100 Hz to 100 kHz on the DIS-7000A and DIS-724A, and 10 to 100 kHz for the DIA-708A current waveform.
Yes. The DIC-706B module records CAN and CAN FD data (ISO/DIS 11898-1) on 6 isolated channels, with timestamps.
It supports trigger synchronization with previous DIS-5000 Series devices, connects to conventional products through cascade cables, and fits conventional vehicle mounting plates with L angle brackets of the same mounting pitch.
DIS-70A control software for Windows 10 and Windows 11, supporting up to 999 channels.
Configure and order the DIS-7000 Series
Configure the DIS-7000 system with the master and expansion modules your crash test needs and request a quote on this page. For questions, contact us.